稀油站油泵工作原理

潤滑油由螺桿泵從油箱中吸出，通過單向閥、雙鼓網過濾器、熱交換器送至設備各潤滑點。每個薄油站配有兩臺螺桿式油泵(一臺備用，一臺使用)。稀油站油泵螺桿泵出口油壓約為0.2mpa。薄油站是薄油循環潤滑系統的心臟，它將潤滑油強制輸送到設備的摩擦部位，在相對運動的機器部件之間形成油膜，減少部件的摩擦磨損，并帶走摩擦產生的熱量，保證機器的運行，延長設備的使用壽命。用于企業電機軸承、粉末分離器軸承、大型風機、軋機軸承。稀油站油泵手動系統 

關閉稀油站油泵把握柜內所有斷路器，將把握柜顯示頁上的“把握模式”開關SA1設置為“單機手動”地區分布(SA1開關有“單機手動”、“DCS把握”和“專業技術電子把握”三個地區分布。選擇把握柜顯示頁上的“單手動”、“DCS把握指示燈”、“專業技術電子把握”指示燈，不同把握方式對應點亮)，“主泵選擇”開關SA2設置為“1#泵”或“2#泵”地區分布(SA2開關有“1#泵”和“2#泵”兩個地區分布，在不同把握方式下，選擇把握柜顯示頁上的“1#泵指示燈”和“2#泵指示燈”)。此時顯示頁上的把握按鈕可用于啟動1#泵、2#泵或熱油裝置。手動系統主要是由于安裝結束后確認螺桿泵的旋轉方向等電氣調試，正常工作一般用自動系統。

稀油站油泵自動化系統自動系統工作時，有“DCS遠程把握”和“就地把握”兩種工作狀態。關閉貧油站把握柜內所有斷路器，將把握柜顯示頁上的“把握模式”開關SA1設置為“專業技術電子把握”地區分布(“DCS把握指示燈亮”)，將“主泵選擇”開關SA2設置為“1#泵”或“2#泵”地區分布，即所選泵為主油泵并開始運行。專業技術電子根據油壓、油位、油溫等信號自動啟動和停止備用泵、電加熱裝置等設備，自動調節整個油站的運行狀態，并可通過把握柜顯示頁上的指示燈和DCS信號檢測運行狀態。當螺桿泵自動穩壓系統開始工作時，如果主螺桿泵出現異常或漏油導致油壓低于0.15mpa，備用螺桿泵將自動開始工作，直到油壓達到正常停止。如果兩個螺桿泵啟動后油壓仍然偏低，系統會發出油壓偏低報警，提示工作人員檢查是否有泄漏或螺桿泵損壞。油箱油溫通過電接點雙金屬溫度計當油箱溫度≥50℃時將報警信號發送給專業技術電子，然后專業技術電子把握其他相關設備。